Condominium booster pump replacement in Manila: sizing, VFD duplex panels, CDL/CDLF booster sets. Nationwide PH supply, install and commissioning, quote in 1 business day.
When a condominium booster pump needs replacement, not repair
Most condominium booster pump replacement calls in Metro Manila start the same way: upper floor units lose pressure during the morning and evening peaks, the pump runs continuously instead of cycling, or one pump in the set has been offline long enough that the building has been running on a single unit.
Survey data we need before quoting a replacement
A replacement quote is only as good as the data behind it, and a condominium pump room imposes constraints a new build does not. Before we size and quote a replacement set, send us the following. First, photos of the existing pump set, the control panel interior, and the pump room including the door and access route, since a set that cannot fit through the door is not a replacement. Second, the nameplate details of the existing pumps: brand, model, kW rating, voltage, and phase. Third, the suction and discharge pipe sizes and the flange or thread type at the tie in points. Fourth, the number of floors served, the height from the pump room to the highest fixture, and the total number of units. Fifth, the number of fixtures by type if the building has as built plumbing drawings. Sixth, the incoming supply voltage, typically 220V or 380V three phase 60Hz in Philippine condominiums. Seventh, whether the building has a cistern and a roof tank or runs direct pressure. With that set we can apply Water Supply Fixture Unit tabulation and Hunter's Curve per the National Plumbing Code of the Philippines (NPCP) to confirm whether the original sizing was correct, because a surprising number of replacements are quietly correcting an original undersize.
Replacement booster pump sets we supply and install for condominiums
We supply and install commercial booster pumps for buildings in two configurations: simplex for straightforward single-pump setups, and duplex where standby redundancy is required so the building is never left running on a single pump. Motors are specified at 220V or 380V three phase 60Hz to match standard Philippine condominium supply. Pumps and panels are sized together as one system rather than selected separately, with the exact flow and head determined by your survey data.
Retrofitting VFD control on an existing condominium set
A large share of older condominium booster sets in Manila are fixed speed with a pressure switch and a hydropneumatic tank. They work, but they cycle hard, they deliver a pressure band that swings with demand, and they draw full motor current on every start. Replacing the control panel with a VFD duplex control panel is often the highest return part of a replacement project. Variable frequency drive control modulates pump speed to hold a setpoint instead of cycling between cut in and cut out, which delivers energy savings in the range of 25 to 40 percent against fixed speed operation, holds pressure to roughly plus or minus 2 psi at the fixture, and removes the hard starts that crack pipework and shorten seal life. We supply and install control panels built with variable frequency drives, rated IP54, with pressure feedback and auto alternation between pumps. In some cases the existing pumps are mechanically sound and only the panel and pressure vessel need replacing, which is a shorter scope and a smaller budget. We will tell you when that is the case rather than quoting a full set by default.
How the work is coordinated with your building team
TankSmith supplies, installs and commissions the replacement under one contract, so there is no handoff between an equipment supplier and a separate installation contractor. Our own team handles equipment selection and sizing review, supply of the pump set, control panel, and pressure vessel, removal of the old set, pipework modification at the tie in points, electrical termination, and commissioning, plus warranty and after sales parts. Your building's own maintenance team stays involved for access to the pump room, scheduling around occupied common areas, and any permits the property or the local government requires, since they know the building and resident impact windows best. We plan the water off window as a single day: the new set is staged and pre tested before the old set comes out, so the changeover is one planned interruption rather than an open ended process. If the retrofit involves panel work only, the same coordination model applies as our VFD panel installation projects.
Lead times, VAT treatment, and requesting a quote
Standard lead time on a condominium booster pump replacement is 21 to 35 days from confirmed order for ex stock configurations. Made to order sets, meaning non standard head and flow combinations, specific model requirements, or custom panel builds, run 45 to 90 days. Installation is scheduled around delivery so the pump room changeover happens as part of the same engagement, not a separate undated callback. If your building is currently operating on a single pump with no standby, tell us in the RFQ, because it changes which configurations we quote first. Pricing is quote based, since the same nominal flow can differ substantially in cost depending on head requirement, panel specification, and pressure vessel size. On tax treatment, 12 percent VAT applies to VAT registered buyers, while zero rated VAT applies to PEZA and SBMA locators and registered exporters with the correct documentation. We cover installs nationwide across the Philippines, including NCR, the rest of Luzon, Visayas, Mindanao, and PEZA, SBMA, and Clark. If the same project needs storage, see industrial water tank supply in Metro Manila and FRP modular water tanks for building cisterns. Send the survey data listed above with your RFQ and we will respond within one business day with a sized recommendation, not just a price list.
Frequently Asked Questions
Equipment lead time is the long pole, not the installation itself. Ex stock configurations ship in 21 to 35 days from confirmed order, and made to order sets, meaning custom head and flow combinations or custom panel builds, take 45 to 90 days. The physical changeover is normally planned as a single day water off window, which is why we stage and pre test the new set before the old one comes out. If your building is running on a single pump with no standby, say so in your RFQ so we quote the fastest available configurations first.
Yes, TankSmith installs it. We supply, install and commission the replacement set under one contract, including removal of the old pumps, pipework modification at the tie in points, electrical termination, and commissioning. Your building's own maintenance team stays involved for access, scheduling, and any permits the property or local government requires, since they know the pump room and resident impact windows best, but the physical pump work is carried out by our own team rather than a separate contractor you need to source.
Often yes. If the pumps are mechanically sound and the failure is in the control side, replacing the panel and pressure vessel is a shorter scope and a smaller budget than a full set. This is common in older fixed speed condominium installations, where swapping to a VFD duplex panel delivers 25 to 40 percent energy savings against fixed speed operation and holds pressure to about plus or minus 2 psi at the fixture. Send us nameplate details and panel photos and we will tell you whether a panel only scope is viable rather than quoting a full set by default.
Sizing comes from Water Supply Fixture Unit tabulation converted through Hunter's Curve to peak simultaneous demand, per the National Plumbing Code of the Philippines (NPCP), plus a head calculation summing static lift, friction loss, and residual pressure at the highest fixture. We supply and install simplex and duplex sets, with simplex suited to straightforward single-pump setups and duplex used where standby redundancy is needed. For residential condominiums we normally recommend duplex so there is always a standby pump. Send floor count, unit count, fixture schedule, and height to the highest fixture and we will run the sizing.
Pricing is quote based and we do not publish prices, because cost varies with head requirement, panel specification, and pressure vessel size. On tax treatment, 12 percent VAT applies to VAT registered buyers. Zero rated VAT applies to PEZA and SBMA locators and to registered exporters that provide the correct supporting documentation, which is relevant for mixed use and BPO occupied buildings inside those zones. Confirm your registration status in the RFQ so the quotation is issued with the correct VAT treatment from the start.
We supply and install vertical multistage centrifugal booster pumps in our CDL and CDLF series, built in stainless steel (SS304), across a 0.37 kW to 200 kW range so sets can be matched to buildings of very different sizes. Control panels use variable frequency drives rated IP54, with pressure feedback and auto alternation between pumps, available in VFD, duplex and simplex, star-delta, SDE and MCC configurations. Pump and panel selection on a replacement comes down to matching flow, head, and standby requirements to your survey data, and we quote the recommended configuration rather than a single fixed line.
Browse more configurations in the water tank systems directory.
Related Pages
- Fristma Booster Pump Supplier in Manila: ISO 9001 Certified Equivalents
- Variable Speed Booster Pump System Quotation for Manila Buildings
- 15 HP VFD Duplex Booster Pump System Supplier in the Philippines
- 10,000 Liter Electrical Water Tank System: Pump, Control Panel, and Tank
- Water Tank and Booster Pump Sizing for Apartment Buildings Up to 6 Storeys
- How a Booster Pump System Automatically Adds Air to a Pressure Tank
Found this useful? Add TankSmith as a Preferred Source on Google so our tank sizing guides show up first next time you search.